Beckhoff CX1100-09xx UPS Instrukcja Użytkownika

Documentation forUPS - Modules for CX10x0-SystemsCX1100-0900 (550 mA / 20 As)CX1100-0910 (1.1 A / 20 As)CX1100-0920 (1.1 A / 40 As)Version: 1.2Datum:

Product overview8 Embedded PCTechnical Data CX1100-0900, CX1100-0910, CX1000-0920The UPS-Modules are available in three versions. The user can choose

Product overviewEmbedded PC 9CX1100-09xx ConnectionsThe UPS-Modules are supplied with power by 5-pin "Open Pluggable Connector". The other c

Product overview10 Embedded PCConnection to power supply For power supply units with K-bus / E-bus connection (CX1100-0002, CX1100-0003 und CX1100-004

Product overviewEmbedded PC 11Power-Fail-Signal ConnectionThe UPS modules can also be used to supply other bus couplers. To use the UPS module with th

Transport12 Embedded PC3. TransportUnpacking, installation and transportThe specified storage conditions must be adhered to (see "Technical data&

Fitting and wiringEmbedded PC 134. Fitting and wiringMechanical assemblyDimensionsThe CX1000 product range is characterized by small overall installed

Fitting and wiring14 Embedded PCCX1100-0910 UPS Module:CX1100-0920 UPS Module:

Fitting and wiringEmbedded PC 15Mechanical installation of the UPS ModuleThe UPS module can be connected to the Embedded PC System at any positions. I

Fitting and wiring16 Embedded PC1.3 Separating the power supply unit, the CX10x0 CPU and other componentsPlace the CX10x0 block onto a suitable suppor

Fitting and wiringEmbedded PC 17Then fix the CX1020 block on the top hat-rail using the latching straps. You should hear a soft click. Do not force th

Commissioning18 Embedded PC5. CommissioningCharging timeThe charging time of the UPS module depends on actual the discharge and can not be measured ex

CommissioningEmbedded PC 19Discharging timeThe measure the time for discharging of the different UPS modules a precision load was connected to the UPS

Commissioning20 Embedded PCThe other UPS module have a maximal load of 1100 mA. The results are shown below.Retention time in relation to load at swi

CommissioningEmbedded PC 21

Commissioning22 Embedded PCMeasurements with sample configurationsAs an example for a real load some Embedded PC configurations have been tested. The

CommissioningEmbedded PC 23The second test configuration is an Embedded PC with maximal configuration. CX1000-System (CX1000-0122) with system interfa

Commissioning24 Embedded PCThe third test configuration consists of a CX1020-System (CX1020-0120). The configuration is typical. Only thesystem interf

CommissioningEmbedded PC 25The next test configuration is a CX1020-system in maximal configuration. The test connections are the same as in the test 2

Commissioning26 Embedded PCThe last tested configuration is a CX900-system (CX9000-0002). The configuration is typical. Video, USB and serial interfac

CommissioningEmbedded PC 27

Table of ContentsEmbedded PC 1Table of ContentsCX1100-09xx, UPS for CX10x0-Systems1. ForewordNotes on the documentation 2Safety instructions 3Document

Commissioning28 Embedded PCSetting retention time The retention time is set via the torque switch.Switch / position retention time0 100 %9 90 %8 80 %7

CommissioningEmbedded PC 29Register settings CX1100-09xxBit7 Bit6 Bit5 Bit4 Bit3 Bit2 Bit1 Bit00x0D1010 IN-RegisterState_3 State_2 State_1 State_0 res

Commissioning30 Embedded PCSettings in the System ManagerThe CX1100-0900 UPS module is inserted as a "Box" under the CX1100 module. You will

CommissioningEmbedded PC 31Enable Automatic Shut Down: If this switch is selected, then TwinCAT is stopped after an adjustable retention time, and &qu

Commissioning32 Embedded PCEnable Automatic Shut Down: If this switch is selected, then TwinCAT is stopped after an adjustable retention time, and &qu

CommissioningEmbedded PC 33Controlling the UPS from the PLCIt is possible to control the UPS module from the PLC. There are two TwinCAT blocks that pe

Commissioning34 Embedded PCDetails of linking signals are given in the documentation for the TwinCAT System Manager.Linking the UPS control block into

CommissioningEmbedded PC 35displayed. The signals are inserted into the "Variable_configuration" file through the "Insert -> All ins

Commissioning36 Embedded PCVARUPS : FB_CX1000UPSHANDLING;END_VARIt is then called from the program with its parameters. There are seven parameters for

CommissioningEmbedded PC 37VARMAIN.UPS.Ii24VState AT %IB0 : BYTE;MAIN.US.IiChargeState AT %IB1 : USINT;MAIN.UPS.QiControl AT %QB0 : BYTE;MAIN.UPS.QiD

Foreword2 Embedded PC1. ForewordNotes on the DocumentationThis description is only intended for the use of trained specialists in control and automati

Error handling and diagnostics38 Embedded PC6. Error handling and diagnosticsLEDs CX1100-09xxThe UPS-Modules show their state of operating via status

DecomissioningEmbedded PC 397. DecomissioningRemoval and disposalA CX10x0 hardware configuration is dismantled in 2 stages:0. Switching off and discon

Decomissioning40 Embedded PC2. Separating the individual modules2.1. Separating the power supply unit, the CX10x0 CPU and other componentsPlace the CX

AppendixEmbedded PC 418. AppendixCertificationsAll products of the Embedded PC family are CE, UL and GOST-R certified. Since the product family is con

Appendix42 Embedded PCSupport and ServiceBeckhoff and their partners around the world offer comprehensive support and service, making available fast a

ForewordEmbedded PC 3Safety InstructionsSafety RulesThe responsible staff must ensure that the application or use of the products described satisfy al

Foreword4 Embedded PCDocumentation Issue StatusVersion Changes1.2 technical data for charge capacity corrected1.1 annotations to usage of CX1100-0900

Product overviewEmbedded PC 52. Product overviewAppropriate UseThe CX1020 device series is a modular control system designed for top-hat rail installa

Product overview6 Embedded PCSystem overviewUPS module is available in three variations: CX1100-0900 CX1100-0910 CX1100-0920The UPS module is used

Product overviewEmbedded PC 7sample configuration 2: